Frame A Square Piece Of Art Glass With Zinc Came

Flip the frame over so the back faces up. Cut two six-inch pieces and one 4-1/2-inch length of zinc "U" channel with diagonal pliers. Place the short piece of "U" channel at the bottom of the glass window, with the "U" facing the glass.

Frame a square piece of art glass with zinc came. Cut pieces of zinc H-channel metal, which serve as reinforcement bars, or rebar ribs that stretch through the stained glass window from one side of the window to the other. Plan the ribs so that they cross the longest dimension of the window, dividing the window into areas which are each less than 3 square feet. Unless there is sufficient attachment of the zinc border came to the panel, the whole panel can sag within the zinc border, pull away, and fall out. It has happened. Any door panel larger that 4 square feet in area, or having 8 perimeter feet will require reinforcement to maybe and hopefully hold it together when the door slams shut. We will be using zinc channel, zinc channel comes in a six foot length, so we will have to cut this down to size to make it a little more usable. It is made out of a flat piece of zinc that is enfolded by a machine into this form that creates a channel which holds the glass and a body. The face is the width of that body. Stained Glass Zinc Frame. A stained glass zinc came frame is a good option for the edges of your panel. This is for a couple of reasons. If you have a heavier panel that needs a bit of strength, or want a definite border for artistic reasons, then a stained glass zinc frame is your answer.

This is a bright silver colored, heart-shaped steel frame, which you can use to frame your stained glass piece. It is made of 7 gauge (1/8" thick) wire. The heart is 7-3/4" at its widest point across and 7-3/4" (197mm) high. Your creation will not only have a smooth outer edge, but also will have much more stability and rigidity. Next take the came and with your hands simply bend the zinc back and forth until the piece breaks in half! To bend "U" shaped came for a box or other piece where you want to make a 90 degree bend, (but NOT to fully cut the came in half), just cut into both sides of the came with hand held cutters and then bend the came 90 degrees. Oak Hardwood Framing Our framing stock is available in 5 sizes, as shown. Though individual tastes may differ, w e believe that the narrow framing is most suitable for panels up to 4 square feet, and the wide for panels up to 14 square feet. A 2" extra-wide frame is also available. Always place the full length of zinc came from top to bottom along the left and right sides of a window. The top and bottom pieces should fit inside the vertical pieces of zinc where they are nestled in between these vertical pieces. The hooks would then be attached to the vertical pieces of zinc. Like this.

Zinc will react to the patina and turn black and then try to turn the rest of the lead black instead of copper. 7. Once the reaction has taken place we can clean the window again.. the binding butyl rubber from sticking to the art glass.. They really look like a piece of art. Lead came construction was the original stained glass technique used throughout history in church cathedrals. During the Victorian Era it found its way into the home and has remained popular ever since. The pleasing symmetrical lines and ability to withstand changing weather conditions make it ideal for large windows and doors. Lush golden grapes, gracefully entwined by grapevines and ribbons, are the subject of this stunning piece of hand-painted art glass! Zinc-framed, this impressive R-size vertical piece measures 10.25" wide x 42" high. It features two soldered metal rings along the top for hanging. Made with tempered glass for strength and safety. Lead came is intended to be stretched before use. This is why we can roll the came or curve over once to save on shipping. If you do not intend to stretch the came or wish to have it sent straight in a 6ft Box, please see the additional charges below and put in the Special Instructions of your order that is how you wish the came to be packed.

Many glass artists use a rigid came border for projects that are 1 square foot or larger. For projects smaller than 1 square foot, additional options include simply tinning the edge, applying a piece of copper wire or braided copper wire to the perimeter, or soldering ball chain around the border to give a decorative touch and add strength. At Laws Stained Glass Studio, we coat our steel braces in zinc to further prevent rusting. The second reason is prevent a shadow caused by the steel brace. By placing the bar on the inside, it will not give a shadow on the glass. The steel braces are part of the window panel, which is not over 15 square feet. Stained Glass Zinc Frame A stained glass zinc came frame is a good option for the edges of your panel. This is for a couple of reasons. If you have a heavier panel that needs a bit of strength, or want a definite border for artistic reasons, then a stained… The second method is similar to glass on an exterior door, with strips of molding holding the glass inside the frame. Either method works fine, but the dadoed or channeled frame is stronger.