Getting A Paint Sample Off Wall

Paint stores seem to want minimum size of a quarter. FYI, it is almost impossible to get an exact match -- so if it matters to you, I would only do this for small inconspicuous areas or to do an entire wall. Even then, the new paint may not wear the same as the old.

Getting a paint sample off wall. Therefore, you need to remove a paint sample from the wall with the color you want to match. Step 1. Watch the paint. When it begins to bubble, turn off the heat and get your scraper. Step 3 Hold the scraper at a 30-degree angle from the surface of the wall and push downward. Hold the heavy-duty plastic bag below it to catch the falling paint. Take a Sample Paint Chip and Analyze. The first thing you need to do is take a chip of paint off the existing wall, one at least the size of a quarter. Also, make sure it is a clean piece of paint so that you can match the color more accurately. The best method for removing paint is to start at the bottom of the wall and use a razor blade to. Paint sample from wall - help needed. Getting chips of paint off of that big enough to match is hard. If you have a place that is flaking that is usually the only way to get a big enough piece. Cut an oval-shaped, 1"x 2" slot in the wall, piercing only through the surface of the paper... an eighth of an inch deep is plenty. Use the knife to lift a corner of the paper, and then peel it from the wall. Take this sample to the paint store for matching. The cleaner the cut, the easier the patching.

This will help to make the task at hand much easier. Wipe the wall down with a damp, soft cloth. Make sure that you get all pieces of loose paint as well as any dirt off of your wall. Step 3 - Scrape. Once the wall is clean, you will need to get your scraper out and place the blade part of it up against your wall. Try softening the paint with a few drops of olive oil. Cover the paint with a cloth and let the oil soak in for about an hour. If the treatment works, you should be able to wipe off the paint with. STEP 3: Scrape the paint. Take a paint scraper, and chip off the bubbled paint from all the flat surfaces of the metal. For crevices and harder-to-reach areas, switch to a scrubbing pad or nylon. It’s a common image: Someone selecting a wall color paints several sheets of paper or sample boards and hangs them on the wall to compare colors. It looks artistic and even a bit hip, but it may not be the most accurate way to vet wall paint and paint samples. We talked to five pros, including painters and designers.

3-inch flat heavy-duty scraper: With its handle, this scraper gives you a firm grip as you push into the paint. This tool is flat and is shaped like a large putty knife. 2.5-inch two-edge paint scraper: Shaped like a large facial razor, this tool has a thin handle and a wide head.The head sometimes has replaceable scraper blades; shift to a new blade whenever the old one gets dull. If you need to match a paint color, and you do not have any old, unused paint to go by, you can get a paint chip from the painted surface, and take that paint chip to the paint mixers to have them match the color. After you get the new paint, you can touch up the spot from which you chipped the paint. Paint the stripper onto a small area of your wall with a paintbrush and allow it to sit on the surface for about five minutes, unless otherwise instructed by the product's manufacturer instructions. METHOD 5: Compare to Paint Chips. Want to match that pale yellow, bright blue, or stormy-sky-gray wall or furniture? Then head to your favorite paint store, and gather up a selection of paint.

Scrape off a 1 in (2.5 cm) sample of drywall paint with a razor knife. If you’re trying to match paint on sheetrock or drywall, the easiest way to get a perfect match is to bring a sample with you to the paint store. Try to get as much paint off the wall as possible. To use a paint scraper, place the blade at the bottom of the paint you wish to remove, apply pressure so the blade slides under the paint, then peel the paint off as you slide the paint scraper upwards. If there are any awkward spots, try using toothpicks or toothbrushes you don't plan on using. Getting a custom matched color for stucco works the same way it does for getting a custom color match for paint. You need to bring in a clean sample around 1 1/2" x 1 1/2" in size to a stucco supplier or stucco manufacturer and have it matched. They will take that color, get a formula together, make that color and make a sample for you on a. We were testing out samples on our bathroom wall, the worker said that the samples are in an eggshell finish, and the sample looked great when dried... So I thought why not just use the rest of the sample (1 quart benjamin moore sample) and finish this wall!. When I went back to the paint store to get it in a glossy finish, they told me that the sample paint technically isn't real paint.